Guitar Styles

How to get metalcore guitar sound?

Get a tight metalcore guitar sound with a noise gate, a tube-screamer boost, a high-gain amp or modeler, humbucker pickups and careful EQ and recording tips.

On this page
  1. The short answer
  2. Start with your playing
  3. Pick the right guitar and pickups
  4. Put a boost in front of a high-gain amp
  5. Keep the gain moderate
  6. Add a noise gate
  7. Amp or modeler: the common options
  8. Cabinet and mic or IR
  9. EQ and filtering
  10. Double-track rhythm guitars
  11. Strings and setup for low tunings
  12. Common misconceptions
  13. Safety
  14. Where to go next

A tight metalcore sound comes from a short, simple chain: a noise gate, a tube-screamer style boost, a high-gain amp or modeler, and a 4x12 cabinet or a good impulse response. Use high-output humbuckers and keep the gain moderate. Your palm muting matters as much as any gear.

The short answer

For a heavy, tight metalcore tone, you need four things: a gate to control noise, a boost to tighten the low end, a high-gain amp or modeler with a moderate gain setting, and a cabinet sound that matches. Then double-track the rhythm guitars and filter the low and high ends during the mix.

Start with your playing

Gear cannot fix sloppy technique. Clean, tight palm muting and steady picking are the foundation of a metalcore tone. Practice your chugs slowly with a metronome before you judge the sound. If the chugs blur together, turn the gain down before you change the amp.

Pick the right guitar and pickups

Metalcore players usually choose high-output humbucker pickups in the bridge position. Active pickups, such as EMG 81 models, respond quickly and keep the low end tight. Passive and hybrid options, such as Fishman Fluence or Seymour Duncan models, are also common. Active pickups are not required for the sound, so choose the pickups that feel right for your budget and playing.

Drop tunings are common in metalcore, so pair the guitar with a set-up that holds up under low tuning (see the strings section below).

Put a boost in front of a high-gain amp

A Tube Screamer-style pedal (a TS9 or TS808, or a clone) placed before the amp is a common choice. Set the drive low, the level higher, and the tone around noon. The boost does not add much distortion on its own. It tightens the low end and pushes the front of the amp, which keeps the riffs defined. Overdrive vs distortion pedals explains how this kind of pedal differs from a distortion.

Keep the gain moderate

Most players use less gain than they expect. Too much gain turns heavy riffs into a fizzy, loose blur. Start with the amp’s gain lower than you think, and raise it only until the chugs sound clear. The boost plus moderate gain usually sounds tighter than maxed-out gain.

Add a noise gate

High gain amplifies hum and noise, so a noise gate is essential in metalcore. Place it at the front of the chain, before the boost and the amp. Many amps and modelers also include a gate you can use instead. What a noise gate does explains the threshold and other controls. Set it so that the noise stops between chugs without cutting off the notes you want to keep.

Amp or modeler: the common options

Classic high-gain amps include the Peavey 5150 or 6505, the EVH 5150III, the Mesa/Boogie Dual or Triple Rectifier, and the Engl Powerball or Fireball.

If you want a lot of sounds in one unit, modelers are widely used. Common choices include the Neural DSP Archetype plugins and Quad Cortex, Fractal Axe-Fx and FM9, Kemper, and the Line 6 Helix.

Cabinet and mic or IR

The reference metalcore sound uses a 4x12 cabinet with Celestion Vintage 30 speakers, miked with a Shure SM57 up close. If you use a modeler or a plugin, an impulse response (IR) of a similar cabinet and mic setup gives you the same starting point.

EQ and filtering

When you record or mix, use filters rather than heavy boosts. A high-pass filter somewhere around 80 to 120 Hz removes rumble that does not help the chug. A low-pass filter somewhere around 8 to 12 kHz removes harsh fizz. Cutting some mud in the 200 to 500 Hz range can clear up the riffs. The exact points vary with the guitar, cabinet and song, so adjust by ear.

On the amp, avoid boosting the bass to get more weight. It usually makes chugs muddier, not bigger.

Double-track rhythm guitars

Most metalcore rhythm parts use two separate takes of the same riff, panned hard left and right. This gives the wide, wall-of-sound sound. Identical copies of one take do not work, because they sound like a single guitar. Each take needs its own small timing and feel differences.

Strings and setup for low tunings

Use fresh strings in a gauge that suits the tuning. Heavier strings keep the chugs defined under high gain. Check the intonation and action after you change to a low tuning, because the strings will behave differently. See how to intonate a guitar with a tuner.

Common misconceptions

  • More gain does not mean heavier. Excess gain sounds fizzy and loose.
  • Boosting the bass does not add weight. It usually makes the chugs muddy.
  • Active pickups are not required. Passive and hybrid pickups can work well.
  • Expensive gear will not fix sloppy palm muting. Technique matters as much as the chain.

Safety

High-gain amps are loud. Use hearing protection when you practice at volume and at gigs. Tube amps hold dangerous voltage even when they are unplugged, so do not open them unless you have the training to work on them safely.

Where to go next

For the playing side of metalcore, including chugs, breakdowns and tunings, see metalcore guitar techniques. For the power chords that underpin many metal riffs, see how to play power chords on guitar. For timing practice that helps chugs stay in the pocket, see how to learn rhythm guitar.

The complete guide to guitar styles

How to Learn Rhythm Guitar
Read the guide

Keep exploring

Guides from other topics

All topics →