Action is the gap between the strings and the frets. On an electric guitar it is usually measured at the 12th fret: from the top of the fret to the bottom of the string, with the guitar tuned to pitch. Set it too high and the strings are harder to press, and notes can go sharp when you fret them. Set it too low and the strings buzz or choke on bends.
Adjusting action is a small job with a fixed order. Each step changes the ones after it, so work through them in this sequence:
- Tune to pitch, then check and set neck relief with the truss rod.
- Set the bridge saddle height to your target action.
- Check the nut slot height.
- Recheck intonation.
- Set pickup height.
Relief comes first because the truss rod changes the shape of the neck, and that shape sets the string height you then adjust at the bridge.
What you need
- A steel rule marked in 64ths of an inch or in 0.5 mm
- Feeler gauges
- The truss rod wrench or nut driver for your guitar, and the hex key or screwdriver for your bridge
- An accurate tuner
- A capo
- Fresh strings. Old strings stretch unevenly and can throw off the setup. See how to change guitar strings.
A radius gauge is optional but helps when you set the bridge.
Step 1: Check neck relief
Relief is the slight bow in the neck that gives the strings room to vibrate over the middle frets. Check it with the strings on and tuned to pitch:
- Place a capo on the 1st fret.
- Fret the low E string at the last fret where the neck meets the body, often around the 17th fret.
- Measure the gap between the string and the top of the frets at about the 7th or 8th fret, using a feeler gauge.
A common target is about 0.010 inch (0.25 mm). Many electrics fall somewhere in the range of about 0.006 to 0.012 inch, and personal preference matters.
Adjust the truss rod only in small steps. Turning it clockwise, as seen from the adjustment end, tightens the rod and reduces relief. Turning it counterclockwise adds relief. Move it 1/8 to 1/4 turn at a time, then retune and wait before you measure again. The neck can keep moving for minutes or even a day after an adjustment.
If the wrench won’t turn smoothly, stop. Forcing a truss rod can strip the nut or snap the rod. A rod that is maxed out or seized needs a luthier. For the full procedure, see adjusting a truss rod with the strings on.
Step 2: Measure and set the action at the bridge
Stand the steel rule on top of the 12th fret and measure down to the bottom of each unfretted string. For a common starting point on an electric, aim for about 1.5 mm (4/64 inch) on the high E and about 2.0 mm (5/64 inch) on the low E. Some players go a little lower for faster playing, and some go higher if they play hard. Treat these numbers as a starting point, not a rule.
Measure every string, not just one. The strings should sit at an even height across the neck, and the saddles should follow the curve of the fretboard. Because the board is curved, the middle saddles usually sit a little higher than the outer ones. A radius gauge helps you match the saddle heights.
How you adjust the bridge depends on its type:
- Strat-style bridges: each saddle has small hex screws for height. Turn both screws on a saddle by the same amount so the saddle stays level.
- Tune-o-matic style bridges: turn the thumbwheels or posts on both sides evenly.
- Floyd Rose-style tremolos: height changes through the pivot studs and the springs. Detune first, and many players hand this job to a tech.
Make changes in small steps. Retune after each one and measure again. Changing the saddle height also changes string tension and length, which can shift intonation, so check it again after you finish. Once the action is set, play across the neck at your normal picking strength and listen for buzz. If you hear it, see how to fix guitar string buzz.
Step 3: Check the nut
The nut is a separate check. Hold the low E at the 3rd fret and look at the gap over the 1st fret. It should be very small, close to paper-thin.
If the gap is large, the nut slot sits high, and the first position will feel hard to press. If the string touches the 1st fret, the slot is too low, and the open strings may buzz.
Filing a nut is permanent. If the slots need work, leave it to a tech unless you already know how to file them correctly.
Step 4: Recheck intonation
Raising or lowering the saddles changes string tension and length, so intonation can shift. Check it after every action change. The steps are in how to intonate a guitar with a tuner.
Step 5: Set pickup height
Set pickup height last. A pickup set too close to the strings can dampen string vibration and reduce sustain. A pickup set too far away gives less output. For how pickup choice and height shape the sound, see how to set your guitar tone.
A common starting point for Fender-style single-coil pickups is about 8/64 inch on the bass side and 6/64 inch on the treble side, measured with the last fret held down. Humbuckers often start around 3/32 inch on the bass side and 1/16 inch on the treble side. Values vary by pickup, so check the maker’s spec when you can.
Common mistakes
- Using the truss rod to set action. The truss rod sets relief, not action height. Tightening it removes relief and can make buzz worse on the lower frets.
- Measuring at the 1st fret. That reading shows the nut height, not the overall action.
- Chasing the lowest possible action. Very low action causes buzz and notes that choke out on bends.
- Forcing a stiff truss rod. Stop at firm resistance.
- Blaming the bridge when the neck is the problem. If the saddles bottom out and the action is still high, the neck may need a shim or a neck-angle fix. That is a job for a tech.
When to see a tech
Take the guitar to a tech if the frets are worn or uneven, the neck is twisted rather than just bowed, the truss rod is seized, the nut needs recutting, or you’re setting up a floating tremolo for the first time.
Common questions
What should action be on an electric guitar?
Measured at the 12th fret, a common starting point is about 1.5 mm (4/64 inch) on the high E and about 2.0 mm (5/64 inch) on the low E. Playing feel matters more than any single number. A good setup has no fret buzz, clean notes across the neck, and strings you can press without strain. If pressing the strings hurts, see left hand pain from guitar.
What happens if your pickup is too high?
A pickup set too close to the strings can dampen string vibration, reduce sustain and change how the strings feel. If it’s too low, the output drops. Set pickup height after the action and intonation are done, and start from the maker’s spec.
What is the 3 fret rule on guitar?
The 3-fret rule is a quick nut check. Fret the string at the 3rd fret and look at the gap over the 1st fret. The gap should be very small, close to paper-thin. A large gap means the nut slot sits high. If the string touches the 1st fret, the slot is too low, which can cause open-string buzz. The phrase has other meanings too; what is the 3 fret rule on guitar covers the scale-shape use.
Can I adjust a truss rod with strings still on?
Yes. Truss rods are normally adjusted with the strings on and tuned to pitch, so you can see the real result. Many techs slacken the strings slightly before tightening, then retune and measure. Turn the rod in small steps and let the neck settle before you judge the result. For the full procedure, see adjusting a truss rod with the strings on.
Next steps
If your strings buzz after setup, start with the guitar string buzz guide. If new strings keep going out of tune, see why your guitar keeps going out of tune.