A buzzing high E on an acoustic most often comes from a nut slot that is cut too low or worn. It can also come from a high fret, too little neck relief, a low saddle, or a string or bridge pin that isn’t seated properly. Where the buzz happens tells you which one to check first.
Find where the buzz happens
- Open high E only: the nut slot for that string is usually too low or worn.
- One fret only: a high or lifting fret just above the note you are playing.
- Many frets: the action is too low, the relief is too small, or the humidity has changed.
- Higher frets or during bends: a low saddle, too much relief, or heavy picking (see guitar picking technique).
- A rattle near the bridge: the bridge pin, the ball end, or an old or kinked string.
Start with the cheap checks
Swap old or kinked strings first. Old strings lose stability, and a kinked string can buzz against the frets. If you recently moved to a lighter gauge, the lower tension may be the cause, so try a set with a bit more tension. For choosing strings, see guitar string types.
Seat the string and bridge pin
- Push the bridge pin in firmly while you pull up gently on the string. This seats the ball end against the bridge plate. A ball end that isn’t seated can buzz, and it can creep flat over time.
- Check that the string sits in its slot at the nut and in its slot on the saddle.
- Check the break angle over the saddle. The string should bend over the saddle, not lie flat on it.
Check the humidity
Dry air below about 40 percent relative humidity shrinks the top. That can lower the action and make frets stick out, which makes buzz more likely. Many guitarists aim for about 45 to 55 percent. Above about 65 percent, the wood can swell and glue joints can give way, so don’t over-humidify.
A buzz that appears in winter usually means dry air. Humidify the guitar before you change the setup. Shimming a saddle on a dry guitar treats the symptom, while the humidity is the cause.
Check relief and action
- Relief: measure at the 7th or 8th fret. On many acoustics, a healthy range is about 0.004 to 0.012 inch. Adjust the truss rod only if the relief is off, and only in 1/8 to 1/4 turn steps. See adjusting a truss rod with the strings on.
- Action: on many acoustics, the high E sits around 2 mm (about 5/64 inch) at the 12th fret. If the action is too low, the usual fix is a saddle shim or a new saddle. Removing material from a saddle can’t be undone, so a shim or new saddle is often the safer first step.
Tightening the truss rod doesn’t raise the action. It reduces relief, which can make the buzz worse.
Check the nut slot and frets
- If the open high E buzzes, the nut slot is the likely cause. A luthier can shim the nut or recut the slot.
- If one fret buzzes, a luthier can seat, level or crown that fret. A single high fret doesn’t always mean a refret.
Loose parts and sympathetic buzz
Some buzz comes from parts other than the strings or frets:
- Loose tuner bushing nuts
- The truss rod cover
- Pickup wiring or the battery bag
- A loose brace inside the body
A loose brace usually buzzes when you tap the top of the guitar near it. Fixing a loose brace needs a luthier.
When to see a luthier
Try the string, seating and humidity checks first. If the buzz continues, or it traces to the nut, a fret, the saddle, or a loose brace, take the guitar to a luthier or a tech.
Common misconceptions
- The high E can’t buzz because it’s thin. The high E is often set lowest on purpose, so it is one of the strings most likely to buzz.
- Tightening the truss rod raises the action. It reduces relief instead.
- Shimming a dry saddle fixes the problem. Humidifying fixes the cause.
- All buzz comes from the frets. Sympathetic rattles from loose parts are common.
Safety: Don’t over-humidify. Above about 65 percent, the wood risks swelling, and glue joints can fail.