Guitar Setup

Can I adjust a truss rod with strings still on?

Yes, you can usually adjust a truss rod with strings on. Learn how to set neck relief in small steps, which way to turn, and when to stop before forcing it.

On this page
  1. Why strings-on adjustment is normal
  2. What the truss rod controls
  3. Measure relief first
  4. Turn the rod in small steps
  5. Find the adjuster
  6. Stop if it resists
  7. After you adjust
  8. Common triggers
  9. Common misconceptions

Yes. You can usually adjust a truss rod with the strings on, and most guitarists and techs do it that way. Tune the guitar to pitch, make a small adjustment, then retune and measure. The truss rod sets relief, which is the slight bow in the neck. It doesn’t set the action directly. Action is the string height at the bridge and the nut.

Why strings-on adjustment is normal

A truss rod is normally adjusted with the strings on and tuned to pitch, so you see the real result. Many techs slacken the strings slightly before tightening, to ease the load on the rod, then retune and measure. Loosening the rod under full string tension is fine.

What the truss rod controls

Relief is the gentle curve in the neck that gives the strings room to vibrate over the middle frets. Too little relief can cause buzz on the lower frets. Too much relief can cause buzz higher up the neck and can make the strings harder to play.

Relief changes how the strings sit over the middle frets, so it affects buzz and action. But the bridge and the nut set the action itself.

Measure relief first

  1. Tune the guitar to pitch.
  2. Place a capo on the 1st fret.
  3. Fret the low E at the last fret where the neck meets the body.
  4. Measure the gap between the string and the frets at about the 7th or 8th fret, using a feeler gauge.

Typical relief on an electric is about 0.010 inch (0.25 mm). On an acoustic, about 0.004 to 0.012 inch is common. Preferences vary.

Turn the rod in small steps

  • Turning the rod clockwise, as seen from the adjustment end, tightens it and reduces relief.
  • Turning it counterclockwise loosens it and adds relief.
  • Move in steps of 1/8 to 1/4 turn at most.
  • After each step, retune, then wait before you measure again. The neck can keep moving for minutes or even a day.

Dual-action rods can push the neck in either direction, so turn past the neutral point with care.

Find the adjuster

  • Headstock: many electrics, and some acoustics, have the adjuster at the headstock, under a cover.
  • Neck heel: some vintage-style necks have the adjuster at the heel, which is harder to reach. A tech may need to do it.
  • Soundhole: many acoustics have the adjuster inside the soundhole. You’ll need a wrench with an angled head to reach it.

The tool size depends on the maker. Gibson-style rods typically take a 5/16-inch nut driver. Look up the size for your guitar before you turn anything.

Stop if it resists

Stop at firm resistance or any creaking. Forcing the rod can strip the nut or snap the rod. A rod that won’t move may already be at its limit or seized. A luthier should look at a seized rod. If you’re buying second-hand, what to check on a used guitar includes the truss rod.

After you adjust

Check things in this order:

  1. Retune.
  2. Recheck relief.
  3. Recheck action.
  4. Recheck intonation.

For the full setup order, see how to adjust action on an electric guitar and how to intonate a guitar with a tuner.

Common triggers

Relief often needs a new check after:

Common misconceptions

  • The truss rod sets action height. It sets relief, not action.
  • You need to remove the strings. You don’t.
  • The result is instant. The wood settles over hours, sometimes a day.
  • A full turn is a small adjustment. It isn’t. Start with 1/8 turn.

Safety: Stop at firm resistance or creaking. Forcing a truss rod can strip the nut or snap the rod.

The complete guide to guitar setup

How to Adjust Action on an Electric Guitar
Read the guide

Keep exploring

Guides from other topics

All topics →