Guitar Tone

Noise Gate on Guitar: What It Does and When to Use One

A noise gate silences your guitar between notes when you stop playing. Learn how it works, what its controls do, where to place it, and what it can't fix.

On this page
  1. How a gate works
  2. The controls
  3. What a gate can’t fix
  4. Setting the threshold
  5. Where the gate goes
  6. When you need one, and when you don’t
  7. Common gates
  8. Common misconceptions

A noise gate silences your guitar signal when you stop playing. It opens when the signal is above a set threshold and closes when the signal falls below it. It removes noise in the gaps between notes, but it doesn’t remove noise under notes you’re playing.

How a gate works

A gate watches the level of the incoming signal. When your playing is loud enough to pass the threshold, the gate opens and the sound goes through. When the level drops below the threshold, the gate closes, and the sound is muted or reduced. That’s why a gate is useful for hum and hiss, which become obvious in the silences.

The controls

Most gates have some combination of these controls:

  • Threshold. The level where the gate opens.
  • Attack. How quickly the gate opens once the signal crosses the threshold.
  • Hold. How long the gate stays open after the signal drops.
  • Release or decay. How quickly the gate closes.
  • Range. How much the gate reduces the signal when it’s closed.

The Boss NS-2 has threshold and decay knobs, plus a mode switch between reduction and mute. Reduction is gentler, and mute cuts the sound off completely.

What a gate can’t fix

A gate only removes noise when you’re not playing. Its limits matter:

  • Noise under played notes stays. A gate doesn’t clean up hum or hiss while you’re playing.
  • Ground hum and bad power aren’t gate problems. A gate won’t fix faulty wiring or a poor power supply.
  • It doesn’t stop feedback while you play. For squeal, why a guitar makes a high-pitched noise covers the causes.

Fix noise at the source first. Humbuckers, shielding, isolated power, and distance from screens and dimmers all help before a gate does. Muting the strings you aren’t playing also cuts noise; see how to mute individual strings.

Setting the threshold

Raise the threshold until the idle noise just disappears, then back off slightly. If you go too high, the gate chokes sustain, cuts chord decays, swallows quiet notes, and can make the sound chatter as it opens and closes.

As a rough DAW starting point, use an attack of 0.1 to 1 ms, a hold of 10 to 50 ms, and a release of 50 to 200 ms. Adjust these by ear, since the right values depend on the sound.

Where the gate goes

Place the gate after the overdrive or distortion, and before delay and reverb. That way the gate doesn’t chop off the tails of your echoes or reverb. How much reverb to use covers the reverb side of that chain.

If the noise comes from an amp’s gain stages, use the amp’s effects loop, if it has one. The four-cable method lets a gate detect the clean guitar signal while it gates the signal after the preamp. The Boss NS-2 and the ISP Decimator G String II support it. It’s more involved, so use it only when simpler placements don’t work.

When you need one, and when you don’t

A gate helps most when:

  • You play high-gain metal or hard rock.
  • You play staccato, palm-muted chugs and want silence between them, as in metalcore guitar techniques.
  • Single-coil hum shows up at high gain.
  • You’re recording and want clean silences.

You probably don’t need one when you play clean or at low gain. In those cases, a gate can do more harm than good.

Common gates

The Boss NS-2, ISP Decimator II, MXR Smart Gate, and Fortin Zuul are common stompbox gates. Many modeling units include a gate built in.

Common misconceptions

  • A gate removes all noise. It only works when you’re not playing.
  • A gate fixes ground hum or bad power. It doesn’t. Fix those at the source.
  • The gate goes first in the chain. It usually goes after the gain stages.
  • A higher threshold is better. It cuts off notes.
  • A gate stops feedback. It doesn’t while you’re playing.

For guitar settings that reduce noise before a gate is needed, see how to set your guitar tone. If single-coil hum is the problem, how to make a Stratocaster sound heavy covers noiseless options.

The complete guide to guitar tone

How to Dial In Lead Guitar Tone
Read the guide

Keep exploring

Guides from other topics

All topics →