Guitar Tone

How Much Reverb to Use on Guitar: Settings and Tips

How much reverb to use on guitar: typical mix levels, decay times for different songs, reverb placement in the chain, and tips for high gain and recording.

On this page
  1. Types of reverb
  2. Mix levels by situation
  3. Decay and pre-delay
  4. Amp reverb knobs differ
  5. Where reverb goes in the chain
  6. High gain: use less
  7. Live and at home
  8. Recording reverb
  9. Spring amps and movement
  10. Common misconceptions

For a sound that’s always on, a reverb mix of about 10 to 20% is a common starting point. Ambient clean tones can go to 30 to 50%. With high gain, use less, because distortion makes the reverb tail blur. Set the level by ear, in the context of the song, not on its own.

Types of reverb

The main types are:

  • Spring. Built into many amps, including a lot of Fender models. It has a characteristic bounce and “drip.”
  • Plate. A smooth, dense reverb common in studios.
  • Room. A short, natural space.
  • Hall. A longer, larger space.
  • Shimmer. Pitch-shifted reverb that adds a bright, airy tail.

Each type suits different music, and the same mix level can sound very different depending on the type.

Mix levels by situation

These are starting points. Pedals and amps differ, so use these numbers as a place to begin.

Situation Typical mix
Subtle, always-on sound 10 to 20%
Ambient clean 30 to 50%
Surf spring Very wet
High-gain rhythm Low, or off

Surf tones are the exception. The Fender 6G15 reverb unit, introduced in 1961 with dwell, mix, and tone controls, is associated with surf music and Dick Dale’s sound. Surf tones rely on a very wet, dramatic spring sound.

Decay and pre-delay

Decay is how long the reverb tail lasts. Rough ranges:

  • Room: about 0.5 to 1.5 seconds
  • Hall: about 2 to 4 seconds
  • Ambient pads: 5 seconds or more

Match the decay to the tempo. Faster songs need shorter tails, or the reverb blurs the rhythm. Slower songs and ballads can handle longer tails.

Pre-delay is the gap before the reverb starts. A pre-delay of about 10 to 40 ms keeps your pick attack clear before the reverb blooms.

Amp reverb knobs differ

Reverb controls don’t mean the same thing from amp to amp, or from pedal to pedal. On a Fender amp with a 1-to-10 reverb knob, about 2 to 3 is subtle. Spring “drip” for surf tones starts around 5 to 6 or higher. Other amps will have different numbers, so trust your ears over the dial.

Where reverb goes in the chain

Put reverb after distortion, and put delay before reverb. If reverb comes before distortion, the sound can get washy. Some players use that deliberately, as in shoegaze.

With amp distortion, use the amp’s effects loop if it has one. That keeps the reverb after the amp’s gain stages.

High gain: use less

Distortion compresses and magnifies the tail, so reverb can blur into a wash. For rhythm parts with high gain, keep the reverb low or off. For leads, a small amount can add space without losing definition. The heavy metal guitar tone guide has more on high-gain settings.

Live and at home

A room adds its own reverb, so use less at a live gig than you would at home. The amp’s reverb and the room together can get muddy quickly.

Recording reverb

When you record, track the guitar dry. Add reverb in the DAW on a send or bus, with the reverb set to 100% wet, so you can control its level separately from the dry sound.

Filter the reverb return too. A high-pass filter around 200 to 300 Hz clears mud, and a low-pass filter around 5 to 8 kHz tames harshness. How to record clean guitar covers the rest of the recording chain.

Spring amps and movement

A spring reverb can make a loud crash if you bump or move the amp. Turn the amp down before you move it.

Common misconceptions

  • More reverb sounds better. It sounds big alone but blurs in a band mix.
  • Reverb hides sloppy playing. It smears timing further.
  • Reverb numbers mean the same thing across amps and pedals. They don’t.
  • Reverb can go anywhere in the chain. Placement changes the sound a lot.
  • Delay and reverb are interchangeable. They do different jobs.

For lead settings with delay and reverb, see how to dial in lead guitar tone. For a jazz-specific approach, see jazz guitar tone settings.

The complete guide to guitar tone

How to Dial In Lead Guitar Tone
Read the guide

Keep exploring

Guides from other topics

All topics →