For a heavy metal sound, use a bridge humbucker into a high-gain amp or a distortion pedal. Keep the gain around 5 to 7 on a 10-point dial rather than at maximum. Keep the mids in, tighten the low end with a boost or a noise gate, and play palm-muted power chords with tight rhythm.
Those are the basics. The rest of this guide explains each step.
Start with humbuckers
Humbuckers handle high gain with less hum and more thickness than single coils, so they’re the usual choice for metal. Passive examples include the Seymour Duncan JB, Seymour Duncan Distortion, Seymour Duncan Invader, and DiMarzio Super Distortion. Active options include the EMG 81 and EMG 85.
You don’t need active pickups or a seven-string guitar to get a metal sound. Plenty of players do well with passive humbuckers on a six-string.
Choose a high-gain sound
You can get a metal tone in a few ways:
- High-gain amps. Peavey 5150 or 6505, Mesa Dual Rectifier, and Engl amps are common in modern metal. A boosted Marshall JCM800 covers more classic territory.
- Modelers. Line 6 Helix, Fractal Axe-Fx, Kemper, and Neural DSP units can produce high-gain tones directly.
- A distortion pedal into a clean amp. A Boss MT-2, Pro Co RAT, or Boss HM-2 can work through a clean amp. The HM-2 is associated with Swedish death metal tones.
Classic metal often leans toward British or vintage high-gain voicings. Modern metal often favors high-gain modern amps. Try a few to hear the difference. For a modern metalcore chain, see how to get a metalcore guitar sound.
Set the gain: 5 to 7, not max
Gain usually works best around 5 to 7 on a 10-point dial. Turn it higher and palm-muted riffs can turn into fizz, loose notes, and noise. Tightness in metal comes more from the mids, the palm mute, and the playing than from maximum gain.
Tighten the front end
A Tube Screamer-style boost in front of a high-gain amp tightens the low end and pushes the front end. Set the drive at 0, the level high, and the tone around noon. The boost helps the riffs stay defined.
A noise gate stops hum and string noise between chugs. Set the threshold just above the idle noise, so the gate closes during rests but doesn’t chop notes. How a noise gate works explains the controls.
Shape the EQ
Starting points, which vary by amp:
- Bass: about 5 to 6
- Mid: about 4 to 6
- Treble: about 6 to 7
- Presence: about 5 to 7
Don’t scoop the mids completely. A full scoop can sound huge alone, but the guitars vanish in a band. Excess bass makes palm mutes boom, and too much treble makes the sound harsh. How to set your guitar tone has the method for finding the right balance.
In a mix, a high-pass filter around 80 to 100 Hz clears low-end mud, and a low-pass filter around 8 to 12 kHz tames fizz.
Cabinets and impulse responses
A 4x12 cabinet with Celestion Vintage 30 speakers is a standard choice for metal. If you use an amp simulator, an impulse response of a similar cabinet makes the sound more realistic.
Tunings and strings
Lower tunings need heavier strings to stay tight. Common examples:
- Drop D: .010 to .052
- Drop C: .011 to .056
- B (seven-string): .012 to .060
Baritone scales of about 26.5 to 28 inches or more also help lower tunings feel tight.
Playing: palm mutes and power chords
Rest the edge of your picking hand near the bridge for tight palm mutes. How to palm mute on guitar covers placement and pressure. Consistent downpicking or alternate picking keeps the riffs even. Mute the strings with your fretting hand so unwanted notes don’t ring.
Power chords, which are a root and a fifth, are the core of most metal rhythm. A one-finger power chord in drop tuning is a good place to start. See how to play power chords on guitar for the shapes.
Recording rhythm guitars
For recorded rhythm tracks, double-track with two separate takes panned hard left and right. Don’t copy and paste one take. Two real takes sound wider and more natural.
Common misconceptions
- Max gain makes it heavier. It usually gets fizzy, loose, and noisy.
- Scoop the mids completely. The guitars vanish in a band.
- You need actives or a seven-string. Passive humbuckers on a six-string work well.
- Pedals can’t do metal through a clean amp. A distortion pedal into a clean amp can work.
Safety
Wear earplugs. The NIOSH recommended limit is 85 dBA over an 8-hour day, and the allowed time roughly halves for every 3 dB increase. Metal can get loud quickly, so protect your hearing at rehearsal and gig volumes.
If you’re weighing a single-coil Strat for metal, how to make a Stratocaster sound heavy covers the pickup and noise options in detail.