You can record a clean electric guitar with a small audio interface, a computer, and a digital audio workstation (DAW). The job is to get a strong, clean signal into the interface without noise or clipping, and to monitor it without a noticeable delay. This guide uses a Focusrite Scarlett Solo as the example, but most of the steps apply to any interface with an instrument input.
What you need
- An audio interface with an instrument (Hi-Z) input
- A mono guitar cable (1/4-inch TS)
- A DAW
- Headphones or studio monitors
- Optional: a dynamic microphone, such as an SM57, for recording an amp
Can you plug a guitar directly into an audio interface?
Yes. Plug the guitar into the instrument input, not the microphone input. A jack-to-XLR adapter into a mic input gives a weak, dull signal, because the impedance doesn’t match a guitar pickup.
Connecting the guitar on a Scarlett Solo
On a Focusrite Scarlett Solo (4th Gen), the 1/4-inch jack is Input 2. Press the Inst button so the input is set for a guitar pickup. The XLR input is for microphones. The layout varies between generations, so check the labels on your unit.
- Use a mono TS cable from the guitar to the 1/4-inch jack.
- Leave 48V phantom power off. Phantom power is for condenser microphones on the XLR input, not for a guitar.
- Pick the matching input in the DAW. Set a mono track to the input the guitar is plugged into.
Set the input gain
Strum at your loudest, then raise the gain until the peaks land around -12 to -6 dBFS on the DAW’s meter. On a Scarlett, the gain halo should stay green, with the occasional amber flash, and never go red.
Record at 24-bit and 44.1 or 48 kHz. 24-bit leaves plenty of headroom, so you don’t need to record hot. Clipping is permanent, so leave room.
Monitoring without delay
Latency is the delay between playing a note and hearing it. While tracking, keep the buffer small, around 64 to 128 samples. When you mix, raise it to 512 or 1024 samples to free up processing power.
The interface’s Direct Monitor gives zero-latency monitoring. Turn it off when you monitor through an amp simulator, or you’ll hear a doubled, phasey signal.
On Windows, install the Focusrite ASIO driver and select it in the DAW. On a Mac, the interface is class compliant and works without a separate driver.
If you still get delay, check the buffer size and driver before you blame the interface.
Raw DI or a clean amp?
A raw DI signal often sounds thin and bright. That’s normal. You can add an amp simulator or an impulse response in the DAW later, or re-amp the recording through a real amp.
To mic a clean amp, place an SM57 about 1 to 2 inches from the grille. Aim at the edge of the dust cap for a warmer sound. Move toward the center for a brighter one.
Clean tones expose noise
A clean recording shows hum and hiss that a distorted amp would hide. Move away from monitors, computers, and dimmer switches. Single coils hum the most, so a humbucker or noiseless single coil helps. A noise gate can clean up the silences between notes. How a noise gate works explains the settings.
Mixing a clean guitar
- High-pass around 80 to 100 Hz to clear low-end rumble.
- Light compression, around 2:1 to 4:1.
- Reverb on a send, not as a permanent insert, so you can set the level by ear. How much reverb to use covers levels.
Fresh strings, tuning, and intonation matter more on a clean recording, because every flaw is audible. See how to change guitar strings and how to intonate a guitar with a tuner.
Why is my Focusrite not picking up my guitar?
Check these in order:
- The cable. Use a mono TS cable, and confirm it works with another device.
- The Inst button. On a Scarlett Solo, Inst should be on for a guitar. Without it, the signal can sound weak or dull.
- The DAW input. Check that the track is set to the input the guitar is plugged into, that it’s mono, and that it’s armed for recording.
- The gain. Strum and watch the meter. Raise the gain if nothing shows.
- The driver. On Windows, confirm the Focusrite ASIO driver is selected in the DAW.
Common misconceptions
- A jack-to-XLR adapter into the mic input is fine. It gives a weak, dull signal.
- Record as loud as possible. Clipping is permanent.
- A thin DI means a bad interface. It usually just means the signal is raw.
- Latency means you need a better interface. The buffer or driver is usually the cause.
Once the signal is clean, you can add reverb to taste. If a whine or hum shows up in the recording, why a guitar makes a high-pitched noise covers the usual sources.